ASTM C582 PDF

ASTM C + REDLINE: STANDARD SPECIFICATION FOR CONTACT- MOLDED REINFORCED THERMOSETTING PLASTIC (RTP) LAMINATES FOR. Start. Standard ASTM standard · ASTM C latest; Reinforced Plastic Piping Systems and Chemical Equipment; Plastic Building Products (ASTM VOL ) . C – 95 – This document is not an ASTM standard and is intended only to provide the user of an.

Author: Meztigrel Tazahn
Country: Paraguay
Language: English (Spanish)
Genre: Music
Published (Last): 10 January 2018
Pages: 310
PDF File Size: 12.55 Mb
ePub File Size: 20.82 Mb
ISBN: 850-2-89183-133-4
Downloads: 16066
Price: Free* [*Free Regsitration Required]
Uploader: Zologal

NOTE 6—The five Arabic grade numbers designate minimum physical property levels of a laminate obtained from tests of representative production process samples.

Astm c-582

Physical and Mechanical Properties 7. Test Method D Surface resin may require the addition of paraffin or may be astmm with overlaid film, as required or approved by the resin producer, to ensure proper surface cure. Pastes shall be made with thixotropic agents. Roll each ply for thorough wet-out and deaeration.

As aztm alternative, a minimum of two passes of chopped roving minimum? NOTE 7—Table 1 and Table 2 are for reference purposes and do not preclude other laminate-type constructions, such as nonwoven biaxial or unidirectional fabric, which may be agreed upon between the buyer and the seller, or may be added to this specification if they have been fully identified and ast, as shown in Appendix X2. A thixotropic agent may be added to the resin for viscosity control. It is informational only c528 not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

  AMAZING LIVER GALLBLADDER FLUSH ANDREAS MORITZ PDF

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

NOTE 7—Table 1 and Astj 2 are for reference purposes and do not preclude other laminate-type constructions, such as nonwoven biaxial asym unidirectional fabric, which may be agreed upon between the buyer and the seller, or may be added to this speci? NOTE 1—The laminates covered by this specification are manufactured during fabrication of contact-molded RTP tanks, piping, and other equipment.

Astm c wilfredo row Enviado por: Parte 1 de 2 C5822 Specification for Contact-Molded Reinforced Thermosetting Plastic RTP Laminates for Corrosion-Resistant Equipment1 This standard is issued under the fixed designation C ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

See Table 1 and Table 2 for standard thicknesses.

Tensile strength, ultimate—17 psi MPa. There is no known ISO equivalent to this standard.

Astm c – astm normas fibra de vidrio

Laminates shall be classified according to type, class, and grade: A surfacing mat is not required unless speci? Current edition approved Oct. Location of exotherm plies may be shifted within the laminate body. This specification is limited to fabrication by contact molding. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Link to C5882 This link will always route to the current Active version of the standard.

  CATALOGO COSTUMI YAMAMAY 2011 PDF

Each pass of chopped roving or ply of chopped-strand mat shall be thoroughly rolled out. NOTE 11—Thicker laminates shall not be used for such tests, as results will vary signi? A thixotropic agent may be added to the resin for viscosity control. ASTM Volume A superscript epsilon e indicates an editorial change since the last revision or reapproval.

ASTM C582 – 09(2016)

Laminate designation from Table 3 shall consist of the abbreviation RTP followed by 1 type in Roman numerals; 2 class in capital letters followed by FS if required; 3 grade consisting of five Arabic numbers to designate minimum levels of physical properties and 4 thickness designated by Asmt number in decimal inches or ALL, if properties apply to all thicknesses.

The initial ply of the v582 lamination shall be 11? Gaps are not permitted. NOTE 1—The laminates covered by this speci? As an alternative, a minimum of two passes of chopped roving minimum fiber length 1 in.

Plastics and is the direct responsibility of Subcommittee D