ASTM D Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils. Oxidation stability baths to meet test method ASTM D Oxidation Bath for ASTM D, IP , ASTM D, ASTM D, IP , ISO , ISO

Author: Malamuro Dailkree
Country: Rwanda
Language: English (Spanish)
Genre: Health and Food
Published (Last): 26 March 2010
Pages: 22
PDF File Size: 3.61 Mb
ePub File Size: 15.45 Mb
ISBN: 887-4-76074-139-6
Downloads: 51394
Price: Free* [*Free Regsitration Required]
Uploader: Maugul

Oxidation Bath with Oxflo Controller

The precision statement for this method was determined on steam turbine oils. The test is considered to start at this point. Once the required bath temperature is found, d934 at that asm Open tube ends to be ground and? Several hours soaking in this manner often serves to loosen all adhering deposits except iron oxide.

All dimensions are in millimetres inches 1. Use Test Method D when the acid number exceeds 0.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed asm If these steels are not available, other equivalent steels may be used, provided they are found to be satisfactory in comparative tests using Test Method D To allow for heating of the stem portion of the thermometer above the immersion point in the upper portion of the test cell, subtract 0.

Soft copper wire of an equivalent grade may also be used. The values given in parentheses are for information only. Add a desiccant bag that has been folded lengthwise to?

An exception is where the oil is known to have a life shorter than h, the sampling is at the discretion of the operator. Slide the catalyst coil over the inlet of the oxygen delivery tube.


NOTE 2—Alternatively, suitably prepared catalyst coils may be purchased from a supplier. The oxidation test tube has a calibration line at mL.

ASTM D Oxidation Stability Baths

Asttm suitable procedure for catalyst storage is given in Appendix X1. To use this indicator, the lower end of the strip is set at the upper oil level when the test is started. Unless otherwise indicated, it is intended that all reagents conform to the speci? Type Stainless Steel, 22 Gage 0. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

The correct level for water additions may, if desired, be indicated by a x943 metal strip Fig. The test continues until the measured acid number of the oil is 2. Originally published as D — Connect the condenser to the cooling water. The number of test hours required for the oil to reach 2. If a viewing window is included in the design, this viewing window shall be?

Immediately after withdrawing the? Alternatively, temperature—measuring devices of equal or better accuracy may be used. The Luer-Lok connector is preferably of elastomeric material, such as poly?

Rinse the tube with n-Heptane to remove traces of oil and any tenacious organic residues. After each oil sample is taken, the indicator is moved to the new oil level before continuing the test. D — 02 Methods D and Awtm use a color change to indicate the titration end point.


Marking the upper oil level of the?

ASTM D – 99 Standard Test Method for Oxidation Characteristics of Inhibited Mineral Oils NO_PDF

A number in parentheses indicates the year of last reapproval. The overall length of the? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

Add the water using the sampling tube and xstm mL capacity syringe. Rinse thoroughly with tap water until all acid is removed. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Standard test method for determination of the sludging and corrosion tendencies of inhibited mineral oils. Summary of Test Method 3.

Need help?

Any arrangement that leads to the coil con? D — 02 All dimensions are in millimetres inches. D — 02 Notes: For overnight storage less than 24 h the coil may be stored in n-Heptane. If more than two results are obtained by one or both of the laboratories, reproducibility can be calculated as indicated in 4.