ASTM E466 PDF

Download scientific diagram | Typical sample for fatigue test according to ASTM E Standard. from publication: Effect of Hot Isostatic Pressure treatment on. ASTM E , Standard practice for conducting force controlled ASTM E , Standard terminology relating to fatigue and fracture testing 1). ASTM E covers axial force controlled fatigue tests of metallic materials in the fatigue regime where strains are predominately elastic, both at initial loading.

Author: Sharan Danos
Country: Oman
Language: English (Spanish)
Genre: Marketing
Published (Last): 6 September 2007
Pages: 191
PDF File Size: 11.74 Mb
ePub File Size: 17.74 Mb
ISBN: 132-2-59742-200-2
Downloads: 32233
Price: Free* [*Free Regsitration Required]
Uploader: Mogal

Threaded end specimens may prove difficult to align and failure often initiates at these stress concentrations when testing in the life regime of interest in this practice. NOTE 1—The following documents, although not directly referenced in the text, are considered important enough to be listed in this practice: It is advisable to determine these surface residual stresses with X-ray diffraction peak shift or similar techniques, and that the value of the surface residual stress be reported along with the direction of determination that is, longitudinal, transverse, radial, and so forth.

Since specimen preparation can strongly in?

Readers are referred to Ref 1 should this occur. This knowledge and care provides the most meaningful and best possible high cycle fatigue life results. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

The trial test specimen should be turned about its axis, installed, and checked for each of four orientations within the? Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

In view of this fact, the method of preparation should be agreed upon prior to the beginning of the test program by both the originator and the user of the fatigue data to be generated.

  ARMAND CONSTANTINESCU CER SI DESTIN PDF

All material variables, testing information, and procedures used should be reported so that correlation and reproducibility of results may be attempted in a fashion that is considered reasonably good current test practice. Thus, when embarking on a program of this nature it is essential to de?

ASTM E466 – Force Controller Constant Amplitude Axial Fatigue Testing of Metallic Materials

The test section length should be approximately two to three times the test section width of the specimen. The trial specimen should be rotated about its longitudinal axis, installed and checked in both orientations within the? This practice is not intended for application in axial fatigue tests of components or parts. The size of the gripped end relative to the gage section, and the blend radius from gage section into the grip section, may axtm premature failure particularly if fretting occurs in the grip section or if the radius is too small.

Testing Procedure Place the specimen securely in the grips of the testing machine.

To do so would require the control or balance of what are often deemed nuisance variables; for example, hardness, cleanliness, grain size, composition, directionality, surface residual stress, surface?

Appendix X1 presents an example of a machining procedure that has been employed on some metals in an attempt to minimize the variability of machining and heat treatment upon fatigue life. ASTM E is limited to the fatigue testing of axial unnotched and notched specimens subjected to aastm constant amplitude, periodic forcing function in air at room temperature.

Obvious abnormalities, such as cracks, machining marks, gouges, undercuts, and so forth, are not acceptable. However, the design should meet certain general criteria outlined below: Regardless of the machining, grinding, or polishing method used, the? The lower the bending stresses strainsthe more repeatable the test results will be from asttm to specimen.

Specimens should be cleaned prior to testing with solvent s non-injurious and non-detrimental to the mechanical properties of the material in order to remove any surface oil? Touchstone is experienced in fatigue specimen preparation to comply with strict sample preparation astk, including surface finish of the machined sample.

  HISTORIA DE LOS MARRANOS CECIL ROTH PDF

The test forces should be monitored continuously in the early stage of the test and periodically, thereafter, to ensure that asrm desired force cycle is maintained. For most conventional grips, good alignment must come about from very careful attention to design detail. Specimens can be round or flat.

Also, Refsalthough they pertain to straincontrolled testing, may prove of interest since they deal with sheet specimens approximately 0. E4666 care to adjust the specimen symmetrically to distribute the load uniformly over the cross section.

ASTM E Load Controlled Constant Amplitude Fatigue Tests of Metals

Give our test engineers a call today for help configuring the best test machine and accessories according to ASTM E Proper machining techniques prevent the introduction of stress risers or crack initiation sites. A number in parentheses indicates the year of last reapproval. This avoids complications that prevent the true strength of the material from being evaluated. The ASTM E axial load fatigue test is used to determine the effect of variations in material, geometry, surface condition, stress, etc.

Current edition approved Nov. Failure may be de? The value of 1. For specimens having a uniform gage length, it is advisable to place a similar set of gages at two or three axial positions within the gage section.

Ra, in the longitudinal direction.

For cylindrical specimens, alignment should be checked by means of a trial test specimen with longitudinal strain gages placed at four equidistant locations around axtm minimum diameter.