The train communication network (TCN) is a hierarchical combination of two fieldbus for data transmission within trains. It consists of the Multifunction Vehicle Bus (MVB) inside each vehicle and of the Wire Train Bus (WTB) to connect the different vehicles. The TCN components have been standardized in IEC IEC and UIC have now been issued as a set of international standards to overcome this situation: IEC , the Train Communication Network. STANDARD. IEC. First edition. Electric railway equipment –. Train bus –. Part 1: Train Communication Network. Matériel électrique ferroviaire .
|Published (Last):||27 February 2009|
|PDF File Size:||8.27 Mb|
|ePub File Size:||2.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
MVB for critical operation such as traction control and signalling in the driver’s cab, and LON for uncritical and slow data transfer, but low-cost connections such as passenger displays and diagnostics. From Wikipedia, the free encyclopedia. The WTB also supports sporadic data transmission for diagnostics.
Additionally more and more components are added to rail vehicles that need far more bandwidth than any field bus can provide e.
Train communication network – Wikipedia
The multifunction vehicle bus connects individual nodes within a vehicle or in a closed train set. But railways certification is costly and not always needed for uncritical applications such as comfort and passenger information.
This was intentional as the fight between the field busses raged in the s and the decision of the IEC that any of the eight field busses was a standard did not help plug-compatibility.
The MVB frames are not compatible with IEC fieldbus frames as it omits most of the preamble synchronization which is not required if zero-crossing detection is possible. Since connectors are exposed and can oxidize, a current pulse is applied at connection establishment to evaporate the oxide layer, called fritting. The physical level is using transmissions at a 1.
The content of the periodic and sporadic frames is governed by the UIC standard. MVB is similar to FlexRayboth have the “process data”, which is called “static segment” in FlexRayand “message 613375, which is the “dynamic segment” and are driven by a fixed TDMA scheme. The maximum distance is determined on the restriction of a maximum allowed reply delay of The connector between the vehicles is the pole UIC connector.
The WTB operates cyclically to provide deterministic operation, with a period of 25 ms, used mainly for the traction control. The train communication network TCN is a hierarchical combination of two fieldbus for data transmission within trains.
Archived from the original powerpoint on When total cost of ownership is considered, the cost of the hardware elements can easily be outweighed by additional engineering costs in the railways market with its small series. While the WorldFIP, CANopen, Lonworks and Profinet are controlled by international manufacturer associations targeting a wide range of application, MVB was tailored to iex rolling stock application, with the goal of plug-compatibility, and therefore allows no options.
613775 two train compositions join, the addresses are reallocated to form a new composition of vehicles with a sequential address. A unique property of the WTB is the train inauguration Zugtaufe in which the newly connected vehicles receive an address in sequence and can identify the vehicle side called port and starboard like in the marine so that doors open on the correct side.
IEC | IEC Webstore
This is not due to the communication technology: Despite the similarities, no rail-manufacturer has considered FlexRay, since they valuated a common solution higher than a multitude of better busses. Vehicles without WTB node “conduction vehicles” are not counted. There is no inauguration, the addresses are statically allocated. The MVB standard was introduced to replace the multitude of field buses in the train equipment. Webarchive template archiveis links CS1 German-language sources de.
Still all the alternate vehicle buses are connected to the Uec Train Bus. The medium consists of a duplicated shielded twisted pair cable, which runs in the UIC cables between the vehicles.
Train communication network
The wire train bus has been designed for international passenger trains with variable composition, consisting of up to 22 vehicles. No repeaters are foreseen since vehicles in between can have discharged batteries. Views Read Edit View history. Interfaces are listed by their speed in the roughly ascending order, so the interface at the end of each section should be the fastest.
The plugs and sockets are the same as used by Profibus with two 9-pin Sub-D sockets per electrical kec. Technical and de facto standards for wired computer buses.
Up to 32 addresses can be dynamically allocated. This explains why MVB and FIP have similar ieec cyclic and event-drivenonly the arbitration method in case of multiple access differs, as MVB used a binary bisection mode relying of collision detection while FIP piggy-backed a “look-at-me” bit over periodic data.
Retrieved from ” https: Running FlexRay with 2. This separation is not always observed.